Driver for external hard drive

Partition style only supports disk volume that is up to 2TB.Therefore, if you initialize a hard drive that is larger than 2TB to MBR, the space that exceeds 2TB cannot be recognized by Windows. That's why your external hard drive showing wrong capacity.▶ Partitions on the external drive are lost or deleted.If one or more partitions on the external hard drive are deleted by accident, the space will be shown as “ Unallocated” in Disk Management and can't be accessed in Windows File Explorer.How to fix “external hard drive capacity not displaying correctly”?From above, you have known some reasons why external hard drive capacity decreased. In this section, we'll discuss what you should do to fix this issue. The below five solutions are carefully collected by us. You can pick the one you are most suitable for and follow the detailed steps. Fix 1. Update external hard drive driver Fix 2. Reformat the external hard drive Fix 3. Wipe the external hard drive to its full capacity Fix 4. Convert the external hard drive from MBR to GPT Fix 5. Recover the deleted partition on the external hard driveFix 1. Update external hard drive driverStep 1. Type "Device Manager" into the search bar and press "Enter".Step 2. Click "Disk drives" to expand the category. Right-click on the hard drive that shows the wrong capacity and select "Update driver".Step 3. Then click on "Search automatically for updated driver software". Windows will now try to automatically update your driver.Follow the next instructions to update the drivers for your external hard drive. If this method doesn't work, try the other four solutions.Fix 2. Reformat the external hard driveTo format a disk, you can try Windows built-in disk formatting utility first. Here, we take "DiskPart" as an example.Step 1. Type "cmd" in the search bar. Right-click on the Command Prompt and select "Run as administrator".Step 2. Input and run the following commands and hit "Enter" after each line.diskpartlist disk (get a detailed list of all disks on your system)select disk n (n is the number of the external hard drive)clean (delete all partitions on

USB 3.0 hard drives are becoming more and more popular over the past few years. However, since the introduction of Windows 10, some users have had problems connecting their USB drives to the computer.Affected users state that their USB 3.0 external drives are not detected in Windows 10.So, we came up with a few solutions for this problem, and you can check them out below.Why does my computer not detect my external hard disk when plugged in?WD devices are great, but many reported that WD My Passport Ultra isn’t detected on their PC. If this happens, the problem is most likely an improperly formatted drive.Your drivers can also be one reason why an external hard drive is not showing up, and to fix that, you might have to reinstall the USB and the external drive drivers.In some rare cases, it’s possible that you have fatal errors on the external hard drive, but that can be fixed by following the solutions from this guide.USB 3.0 drives offer high transfer speeds, but many users have reported issues with their USB 3.0 external drives. Speaking of issues, these are some of the common problems with external drives:USB 3.0 flash drive not recognized in USB 3.0 port – Your USB 3.0 port can’t recognize flash drives, solved by updating your motherboard drivers.External hard drive not showing up in Disk Management – Your cable causes this and can be solved by replacing it.WD, Toshiba USB 3.0 external hard drive not recognized – Update the drivers and firmware for your drive.USB 3.0 external drive not detected Seagate – Update your drivers and firmware and check if that solves the problem.USB 3.0 external drive not detected laptop – Caused by outdated drivers, solved by updating them.External hard disk not showing, working – Check if the hard disk is properly formatted. Set a different drive letter for it.External drive not detected in BIOS – Usually caused by a faulty cable, but problems with the driver or the firmware can also cause this issue.Problem ejecting USB attached SCSI – Update your USB driver inside Device Manager to fix this.Ugreen storage device not recognized – Create a new partition on your drive as we have shown below.USB 3.0 external hard drive not recognized in Windows 10 – Use the Disk Management tool in order to allow Windows 10 to recognize the external hard drive.USB attached SCSI (UAS) mass storage device driver in Windows 11 – Try using a different cable before jumping into any complicated troubleshooting steps.Without further ado, let’s see all the solutions in more detail!How do I fix USB Mass Storage device not showing?1. Update your USB 3.0 controller driverIf you can’t use your USB 3.0 external drive on your PC, the problem might be an outdated driver. That means you can fix the problem by downloading the latest driver for the USB 3.0 controller.You can download the necessary driver right from your motherboard manufacturer’s website.However, if you don’t know anything about your motherboard, here’s a list of

Will permanently delete files from the external drive and your Mac. If you need the files, back up them to your Mac first and then empty Trash.Run Disk Utility to check your external hard driveWhen you can't see files on the external hard drive on your Mac, you can also run Disk Utility First Aid to check if any errors on it block the files from showing up.Open Launchpad > Other > Disk Utility.Select the external hard drive on the sidebar.Click First Aid > Run to check and repair the external hard drive. Find files on the external drive with data recovery software & reformat the diskTo come this far, if files are still not showing up on the external hard drive on your Mac, you are recommended to use a data recovery tool to help you find them. Then, reformat the external drive to make it available for storing data again.iBoysoft Data Recovery for Mac is a well-designed data recovery tool that supports scanning files on external hard drives, USB flash drives, and other storage devices for free. Even if your external hard drive is corrupted, attacked, or inaccessible, this program can help you find the files on the drive.Here's how to use iBoysoft Data Recovery for Mac to recover files on the external hard drive:After that, you can go to Disk Utility to reformat the external hard drive on your Mac.Update the driver of the external hard driveRarely but not never, the driver of the external hard drive